Fishing | Catch Fish Love Fish

Posts Tagged ‘Braid’

If i’m going to fish with like 20 lb braid, do i need to get a special reel? or will my shimano be fine?

Using 50 lb trilene test. I have no idea what mono or flouro is, so i can’t honestly tell you what it is. Lately, i’ve been eying a pack of powerbro braid lately. It looks a lot thinner.
I mostly fish for bass in pretty murky water. However, occasionally i go trout fishing with the same reel.

I’m looking to buy a Daiwa Sealine-X SHA30. The reel is rated for 25 lb mono at 235 yds, I believe. If I put 30 lb, braid on it, will that stress the reel? Thanks.

its a quantum baitcast reel but i dont know which one is better?

The two main reasons have already been mentioned, preventing slipping on the spool, which is self explanatory . Filling to proper level is the other reason. This is most important on a bait cast, conventional reel, much more so than a spinning reel. If the spool is not filled on a bait caster then you have decreased the rate of line retrieval and the castability of the reel. The spool must turn more times when half full to bring in the same amount of line it does when it is full. Casting a full reel is much easier than casting a half full one. Spinning reels use the bail rotating around the spool so there is not problem with retrieve rate, it will effect the way a reel casts however. In both cases fuller is better.
Also as already stated, most braided line comes in small filler spools which may or may not properly fill a reel. Backing is the solution to this problem, has nothing to do with being cheap. It’s all about doing it correctly. I have several reels with 4lb mono that when I fill them I take off half the old line and add about 100-150 yards of fresh on top. I always have fresh usable line and change 2-3 times a summer, I don’t think that’s cheap, it’s smart.
Fisher mentioned using tape to prevent slippage. This works great when you can get a full fill on a reel from a single filler spool. As far as knots go for joining backing to braided line the blood knot works when the two lines are close in diameter. If they have a large difference in diameter then I use a double uni knot. If I took a reel to a tackle store and they tied two lines together with a Granny knot there would be trouble. I would get my money back after beating who ever did it half to death. ( I say half to death because I wouldn’t get my money back, again being smart)
Just a side note, I do have to disagree with Fisher on using super glue. We tested this and found that the glue actually affected the knot strength. The braid part failed. We were setting up Penn Internationals for long range fishing using 80-130lb spectra and attaching 80-100 mono top shots.
WD this is from a west coast perspective, Now you have heard from both sides of the country and both East and West seem to agree. I’ve been filling reels for over 20years, making every kind of splice and knot you can think of. Never had a failure. You should learn to pick you arguments more carefully.

I have a Shimano FX4000 F fishing reel.
the declared line capacity is reads this:
The line capacity for this reel is :
8lbs -240yards 10lbs-200yards 12lbs-160yards
I have a new spool of the braid:
Shakespeare Ugly Braid 20 lb 300 yd
How much and how thick mono should I put on the spool under the braid line? The declared thickness of the braid is:
UBRAID20FG 20 .009 6Lb. Test 300 Green
so equal to mono 6lb.
The reel is declared for the 8Lb thickness of the mono.
Any idea how much of the mono should I put under the braid, so that all the 300 meters of it fit on the Shimano FX4000 F fishing reel?
Thanks,
Ivan

I own a Penn 525GS Mag. I believe it fits 275 yards of 15lb mono. I want to use 20lb braid with an equivelent mono diameter of 6lbs., and need to be able to get long distances for surf fishing. Any help on the mono to braid fishing line conversion would be much appreciated! Thanks.